MacDon M200 Manuel de l'opérateur Page 156
- Page / 234
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MAINTENANCE AND SERVICING - M150 ENGINE
Form 169017 / 169087 / 169095 154 Revision C
c. Loosen compressor mounting hardware (B), and
push compressor towards engine to release belt
(A) tension.
d. Remove belt (A).
e. Insert the drive end of a ½ inch drive ratchet
wrench into the belt tensioner (C).
f. Rotate tensioner counter clockwise until fan belt
(D) can be slipped off pulley (E). Release
tensioner and remove wrench.
g. Remove belt in order 1-2-3 as shown. Route fan
belt around fan, and remove belt.
h. Install new belt (D) around fan and onto pulleys in
order 3-2-1.
i. Insert the drive end of a ½ inch drive ratchet
wrench into the belt tensioner (C).
j. Rotate tensioner counter clockwise until belt (D)
can be slipped onto pulley (E). Release tensioner,
and remove wrench.
k. Check that belt is properly seated in all pulley
grooves.
l. Install A/C compressor belt (A) on pulleys.
m. Pry compressor away from engine so that a force
of 8 to 12 lbf (35 - 55 N) deflects the belt (A) 3/16
inch (5 mm) at mid-span.
n. Tighten compressor mounting hardware (B).
o. Re-check tension, and re-adjust as required.
p. Move maintenance platforms to working position,
and close engine compartment hood.
7.8.11 ENGINE SPEED
The maximum and idle engine speeds are factory
set to the specifications. See Section 4
SPECIFICATIONS.
If specified speeds cannot be maintained, see
your Windrower Dealer.
IMPORTANT
Do not remove any seals from injector
pump. Removal of seals will void the
engine warranty.
7.8.11.1 Throttle Adjustment
The engine speed is controlled with the throttle
lever that is connected to an electronic sensor
inside the console.
The throttle lever in the cab should move the
throttle sensor the full range between slow speed
stop and full RPM stop, without contacting the
console at either position.
If the throttle lever is contacting the console and
interferes with specified engine speeds, the
sensor position possibly requires adjustment. See
your Windrower Dealer.
B
A
1
2
3
E
C
D
A
- M150 & M200 1
- Self-Propelled Windrowe 1
- Proposition 65 Warning 2
- 1 INTRODUCTION 3
- TABLE OF CONTENTS 4
- 2 SAFETY 8
- 7 Revision C 9
- 8 Revision C 10
- Safety Sign Locations 10
- 9 Revision C 11
- 10 Revision C 12
- 12 Revision C 14
- 3 DEFINITIONS 15
- 4 SPECIFICATIONS 16
- SPECIFICATIONS 17
- 4.2 SPECIFICATIONS 17
- 5 OPERATOR’S STATION 19
- OPERATOR’S STATION 20
- 5.2 OPERATOR PRESENCE 20
- 5.3 SEAT ADJUSTMENTS 20
- 5.7 LIGHTS 22
- 5.8 WINDSHIELD WIPERS 25
- 5.9 REAR VIEW MIRRORS 25
- 5.10 CAB TEMPERATURE 25
- 5.11 INTERIOR LIGHTS 26
- 5.12 OPERATOR AMENITIES 27
- 5.13 RADIOS 28
- 5.14 HORN 28
- 5.15 ENGINE CONTROLS/GAUGES 29
- 5.16 WINDROWER CONTROLS 30
- 5.17 HEADER CONTROLS 31
- 5.18.3 OPERATING SCREENS 36
- 34 Revision C 36
- 35 Revision C 37
- AUGER HEADER 38
- 37 Revision C 39
- 38 Revision C 40
- ROTARY HEADER 41
- 40 Revision C 42
- DISPLAY WARNINGS AND ALARMS 44
- 43 Revision C 45
- 6 OPERATION 53
- WINDROWER OPERATION 54
- HEADER - GENERAL 79
- 6.4 HEADER OPERATION 79
- + to increase float, or 82
- HEADER OPERATION - D SERIES 91
- CAUTION 100
- HEADER OPERATION - A SERIES 104
- HEADER OPERATION - R SERIES 112
- SERVICING 118
- 7 MAINTENANCE AND 118
- MAINTENANCE AND SERVICING 119
- 7.4 ENGINE COMPARTMENT HOOD 123
- 7.5 MAINTENANCE PLATFORMS 124
- WARNING 126
- 7.7 OPERATOR’S STATION 128
- 136 Revision C 138
- 7.8.3 OIL LEVEL 138
- 138 Revision C 140
- 139 Revision C 141
- 7.8.5 AIR INTAKE SYSTEM 141
- 140 Revision C 142
- 141 Revision C 143
- 143 Revision C 145
- 144 Revision C 146
- 145 Revision C 147
- 147 Revision C 149
- 7.8.7 ENGINE COOLING SYSTEM 149
- 149 Revision C 151
- 151 Revision C 153
- 153 Revision C 155
- 7.8.10 BELTS 155
- 154 Revision C 156
- 7.8.11 ENGINE SPEED 156
- 156 Revision C 158
- 157 Revision C 159
- 7.9.4 AIR INTAKE SYSTEM 159
- 158 Revision C 160
- 159 Revision C 161
- VALVE REPLACEMENT 161
- 160 Revision C 162
- 162 Revision C 164
- 163 Revision C 165
- 164 Revision C 166
- 166 Revision C 168
- 7.9.7 ENGINE COOLING SYSTEM 168
- 169 Revision C 171
- 171 Revision C 173
- 173 Revision C 175
- 7.9.10 BELTS 175
- 174 Revision C 176
- 7.10 COOLING BOX 177
- 49.75 in 186
- (1263 mm) 186
- 7.13 WHEELS AND TIRES 203
- INTERVAL SERVICE 211
- 8 TROUBLESHOOTING 214
- TROUBLESHOOTING 215
- 8.2 ELECTRICAL 217
- 8.3 HYDRAULICS 217
- 8.4 HEADER DRIVE 218
- 8.5 TRACTION DRIVE 218
- 8.7 CAB AIR 220
- 8.8 OPERATOR’S STATION 222
- 9 OPTIONS / ATTACHMENTS 223
- 222 Model Year - 2010 224
- 223 Revision C 225
- 224 Model Year - 2010 226
- 225 Revision C 227
- 226 Revision C 228
- 227 Revision C 229
- 228 Revision C 230
- 229 Revision C 231
- 230 Revision C 232
- 231 Revision C 233
- 232 Revision C 234
Produits connexes et manuels pour Tracteur MacDon M200
Tracteur MacDon 9352 Spécifications
(115 pages)
(115 pages)
Tracteur MacDon M200 Manuel de l'opérateur
(55 pages)
(55 pages)
Tracteur MacDon M200 Manuel de l'opérateur
(41 pages)
(41 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.186 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels