Macdon DWA for M Series Manuel d'utilisateur

Double Windrow Attachment for M SeriesSelf-Propelled WindrowersSET-UP INSTRUCTION / OPERATOR’S MANUAL / PARTS CATALOGPart # 169216 Revision E

SET UP INSTRUCTIONS 169216 Revision E 8Linkage installation To install linkage, follow these steps: 1. Remove support (A) by removing nut (B). 2.

SET UP INSTRUCTIONS 169216 Revision E 9CAB END  VIEW FROM UNDERNEATH WINDROWER M205 F EF EJAG H 5. M200: Remove four bolts (D) from the front e

SET UP INSTRUCTIONS 169216 Revision E 10 8. Support linkage assembly with a forklift. NOTE: Make sure fork is not lifting against cylinder fitting.

SET UP INSTRUCTIONS 169216 Revision E 11Deck Installation To install the DWA deck, follow these steps: 1. Remove 2X4’s (A) by removing banding (B)

SET UP INSTRUCTIONS 169216 Revision E 12 6. Support deck with a floor jack or fork lift at each end and position the deck pivot (M) in to the linka

SET UP INSTRUCTIONS 169216 Revision E 13Hydraulics installation HYDRAULICS OVERVIEW See following pages 14 to 16 for detailed installation instruct

SET UP INSTRUCTIONS 169216 Revision E 14 1. Install #10 ORB X #10 JIC elbow (A) in port “DWA” on draper drive block. Install #12 ORB X #10 JIC elbo

SET UP INSTRUCTIONS 169216 Revision E 15 6. On M150/M200 Windrower and D-Series draper headers without reverser kit, connect case drain hose (G) to

SET UP INSTRUCTIONS 169216 Revision E 16BA NOTE: Pre-install four bolts (N) and fitting (L) on auxiliary valve block to simplify assembly. 10. Insta

SET UP INSTRUCTIONS 169216 Revision E 174. Cut hole in decal and install ROTARY switch (C) as shown. The hole is already present in the mounting pl

MACDON DOUBLE WINDROW ATTACHMENT

SET UP INSTRUCTIONS 169216 Revision E 18 10. The program in the windrower monitor needs to be changed to recognize the DWA. a. Turn the key on. Pr

SET UP INSTRUCTIONS 169216 Revision E 19 e. M150/M155: Route hose (G) through slot in frame member and secure with cable tie (H) provided as shown

169216 Revision E 20OPERATION Safety signs PART NO. 174683 PINCH POINT- MOVING PARTS STAND CLEAR LOCATED ON LINKAGE ARM (BOTH SIDES) PART NO. 1744

OPERATION 169216 Revision E 21 CAUTION To avoid bodily injury: • Review the safety sections of your windrower and header Operator’s manuals. • Kee

OPERATION 169216 Revision E 22Side delivery draper speed To set the draper speed, turn the draper speed control. (Knob not exactly as shown.) To ad

OPERATION 169216 Revision E 23 To adjust deck height The deck should never touch the ground or excessive wear could occur to some deck components. I

OPERATION 169216 Revision E 24Conditioner forming shield position Make sure forming shield is high enough to clear the deck when it is lowered (G).

OPERATION 169216 Revision E 25Operating recommendations 15, 16, 18, and 20 ft. Headers: On the first pass, the side delivery system is raised and cr

169216 Revision E 26MAINTENANCE/SERVICE Draper Tension Adjustment Draper tension should be just enough to prevent slipping and keep draper from sagg

MAINTENANCE/SERVICE 169216 Revision E 27 DANGER To avoid bodily injury or death from unexpected start-up or fall of raised machine, stop engine, rem

169216 Revision E 1MacDon M Series Self-Propelled Windrower DOUBLE WINDROW ATTACHMENT TABLE OF CONTENTS INTRODUCTION ...

MAINTENANCE/SERVICE 169216 Revision E 28Draper roller maintenance The draper rollers have non-greaseable bearings. The external seal should be check

MAINTENANCE/SERVICE 169216 Revision E 29Idler roller: 1. Raise deck and engage safety pin. 2. Remove front skid. Loosen draper. Draper does not n

MAINTENANCE/SERVICE 169216 Revision E 30Lubrication There are five pivots which require greasing every 250 hours and/or after end of season.

MAINTENANCE/SERVICE 169216 Revision E 31Hydraulic schematics HYDRAULIC SCHEMATIC WITH OLDER DWA DRIVE BLOCK WITH 2,500 PSI RELIEF VALVE AND OLD D

MAINTENANCE/SERVICE 169216 Revision E 32 HYDRAULIC SCHEMATIC WITH NEWER DWA DRIVE BLOCK WITH 2,900 PSI RELIEF VALVE AND NEW DWA LIFT BLOCK 139974

REPAIR PARTS 169216 Revision E 33REPAIR PARTS Serial Number Record the serial number in the space provided. Plate is located on deck at (A).

REPAIR PARTS 169216 Revision E 34Deck, draper, and rollers (illustration 1)

REPAIR PARTS 169216 Revision E 35 REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 172730 DECK – complete with decals ...

REPAIR PARTS 169216 Revision E 36Deck, draper, and rollers (illustration 2)

REPAIR PARTS 169216 Revision E 37REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 7 144833 ROLLER – idler weldment ...

169216 Revision E 2 Published: July 2013 Original Instruction

REPAIR PARTS 169216 Revision E 38Deck supports and linkage (illustration 1)

REPAIR PARTS 169216 Revision E 39 REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 4 172746 ARM – decal assembly ...

REPAIR PARTS 169216 Revision E 40Deck supports and linkage (illustration 2)

REPAIR PARTS 169216 Revision E 41 REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 144590 SUPPORT WELDMENT KIT, consists of 176062, Items 2, 1

REPAIR PARTS 169216 Revision E 42HYDRAULICS AND IN-CAB ELECTRICAL

REPAIR PARTS 169216 Revision E 43 REF PART NUMBER DESCRIPTION QTYSERIAL NUMBER 1 139508 MANIFOLD – DWA drive, see next page for service parts

REPAIR PARTS 169216 Revision E 44Hydraulic Service Components

REPAIR PARTS 169216 Revision E 45 REF PART NUMBER DESCRIPTION QTYSERIAL NUMBER 1 Not Avail. MANIFOLD – DWA drive, to replace complete unit ord

REPAIR PARTS 169216 Revision E 46 Decals REF PART NUMBER DESCRIPTION QTY SERIAL NUMBER 1 176071 DECAL – header position, horizontal forma

NUMERICAL LIST PART NO. PAGE PART NO. PAGE PART NO. PAGE PART NO. PAGE 169216 Revision E 472147 37 10948 43 11695 37 14338 35 16266 41 176

169216 Revision E 3INTRODUCTION The Double Windrow Attachment (DWA) allows the combining of two windrows of conditioned material close together to be

NUMERICAL LIST PART NO. PAGE PART NO. PAGE PART NO. PAGE PART NO. PAGE 169216 Revision E 48163154 45 163155 45 163156 45 163159 45 163160

169216 Revision E 4SET-UP INSTRUCTIONS NOTE: This unit fits only the windrower models listed in the Introduction. It cannot be installed on the M100

SET UP INSTRUCTIONS 169216 Revision E 5CLeave plastic plugs in these two ports. A DDraper drive block installation To install the draper drive block

SET UP INSTRUCTIONS 169216 Revision E 6D D EE M150/M200 BEFORE M150/M200 AFTER M205 DEB M155 E B DDWA DRIVE BLOCK ABED SUPERCHARGE PUMP COOLER BY-PA

SET UP INSTRUCTIONS 169216 Revision E 7C A B M150 / M200 RAIL WITHOUT ADAPTER E D - REMOVEPlatform rail installation To install the platform rail, f